اخبار القسم en

اخبار القسم en

Monday, 04 July 2022 21:41

Discussion of a graduation project entitled "Design and Modification of the Bacterial Incubator for the Laboratory"

Written by

Discussion of a graduation project entitled "Design and Modification of the Bacterial Incubator for the Laboratory"

Under the supervision of Ph. Dr. Enas Saad Mahmoud


Students names
Abdullah Akram
Karar Haider
Shinar Hassan
Mubarak Saleh

Discussion Committee

Ph. Dr. Saad Mahmoud Ali
Ph.Dr. Zahraa Mohamed Abdel Hassan

Asst.lect. Alaa Hussein Younes

 

A microbiological culture or cell culture incubator is a device used to grow and maintain microbiological cultures or cell cultures.The incubator maintains an optimal temperature, humidity, and other conditions such as CO2 and oxygen content of the interior atmosphere. Incubators are used to culture both bacterial and eukaryotic cells and are essential for much experimental work in cell biology, microbiology, and molecular biology.

 

 

Monday, 04 July 2022 21:27

Discussion of a graduation project entitled "Patient Monitoring from Home"

Written by

Each of the fifth stage students, whose names are attached below, discussed a graduation project entitled ((Patient Monitoring from Home)).

Students names:-
1- Wafaa Hassan Ali
2- Aisha Karim Ali
3- Taher Falah Abed Aoun


Supervisor name
Ph.Dr. Ziad Qassem Habib


Discussion Committee
Prof.Dr. Wissam Kazem Hamdan
Ph.Dr. Zahraa Mohamed Abdel Hussein
Asst.Lect. Atheer audience

About the project:-

Where the research dealt with the use of a factory sensor to measure the patient’s temperature, heart rate, electrocardiogram, room temperature and room humidity. The patient can monitor them.

 

 

 

 

 

  

Wednesday, 29 June 2022 17:35

Discussion of a graduation project entitled "Development and validation of biomaterial for biomedical application"

Written by

Discussion of a graduation project entitled "Development and validation of biomaterial for biomedical application"

Where the research dealt with the applications of using nanomaterials extracted from jitosan. At the beginning, an overview of the wound healing process was presented, followed by a discussion on the properties of jitosan and its nanoparticles and their suitability for treating wounds. Then the mechanisms exerted by chitosan nanoparticles (in the wound healing process) were addressed, discussed and analyzed critically and in detailed sections. We mention, among them; hemostasis, preventing infection, immune response (inflammatory) and the time taken to close the wound.

 

Student names:
Ahmed Tariq Tawfik
Taha Qusay Taleb
Bilal Samir
Hussein Ali Mahdi

Discussion committee names:
Prof. Dr. Jinan Star Khashan
Asst.lect. Mays Sabah
Asst.lect. Saad Mahmoud

supervisor name :

Prof.Dr.Sabah saad 

 

 

 

 

   

 

Wednesday, 29 June 2022 17:20

Discussion of the graduation project entitled "Design and implementation of smart hydraulic damper for artificial limbs"

Written by

Discussion of the graduation project entitled "Design and implementation of smart hydraulic damper for artificial limbs"

the project  discusse Smart Hydraulic Damper is part of sem-active type prosthetic Knee. Magneto rheological Damper is type of Smart Hydraulic, which assists prosthetic knee to performing all function with small energy and high control. The principle of MR prosthetic knee depending on spring-damper mechanisn and generater mechanisn wich work harmony together. The spicial properties of MR Damper is low consumption of energy and absorbing shock that causes reduces inflammation in end of transfamer. The results show the designed MR damper is better than off-the-shelf MR dampers for the application

Students names :
Ali Faleh Mortada
Hussein Laith Abbas
Muhammad Mahdi Adnan
Zainab Karim

Discussion Committee:
Ph.Dr. Jamal Mohamed Hamad
Ph.Dr. Enas Saad Mohammed
Eng. Ayoub Qassem

 

Wednesday, 29 June 2022 17:06

Discussion of a graduation project entitled "BUILDING AND DEVELOPMENT OF A PROTOTYPE CENTRIFUGE AND MINI-REFRIGERATOR FOR MEDICAL EQUIPMENT"

Written by

Discussion of a graduation project entitled "BUILDING AND DEVELOPMENT OF A PROTOTYPE CENTRIFUGE AND MINI-REFRIGERATOR FOR MEDICAL EQUIPMENT"

 

Student's name:
1- Ali Abbas Abo Alhail
2- Mustafa Laibi Madah
3- Sajjad Hassan Hawi

supervisors:

Asst. Prof. Dr. Awfa Abdul Rassoul Abdullah
Asst. Lec. Dalia Muhammad Ali

Discussion Committee

ِِAsst.Dr. Alaa Mohamed Dawood
Asst.Lec. Husam Yahya
Asst.Lec. Atheer Jumhur


Centrifugation is a very old technology, and with the advances in the medical field and laboratories, it has faced many challenges. In this project, we have developed effective tools for the centrifugal process. Where we started by designing a centrifuge prototype
body, rotor, motor base, and brake components using the program (AutoCAD) and printed using Anycubic i3 Mega 3D printer. there are safety components including a micro switch or a lid sensor to automatically turn off the motor when the lid is open and a brake unit to stop the motor simultaneously when the user opens the lid.
as well as This mini fridge can store the samples at appropriate temperatures to transfer them to the specialized medical care center to perform the necessary medical tests on them. A temperature range between (5–10 °C) was obtained.

 

Wednesday, 29 June 2022 16:51

Discussion of a graduation project entitled "Preparation of the arc furnace for powder products"

Written by

Discussion of a graduation project entitled "Preparation of the arc furnace for powder products"

 

Student names:

Hassan Riad Majid
malak Hatem Owaid
Nour Al-Huda Riyad Nasser
Zine El Abidine Khaled Ajeel

project supervisor :

Prof. Dr. Marwan Nafeh Ali

Names of the honorable debaters:

Ph.Dr. Ziad Qassem Habib
Asst.lect. Hossam Yehia
Asst.lect. Hoda Taleb

Electric arc furnaces (EAFs) are extensively employed in steel production and nonferrous metal smelting. Typical electric arc furnaces have a power range of 10MW to 100MW. Laboratory electric arc furnace is a minimized AC electric arc furnace which consumes around 5KW of power. The aim of remodeling a minimized EAF is to refine some types of metals to have much better electrical and thermal conductivity, the way of getting these characteristics in laboratory with a cost-effective method is by melting the material using the minimized EAF, then rapidly cooling the molten metal with crushed ice put around the crucible. Using this type of EAF in combination with this cooling method will give smallest grain size possible after the material reforms in a mold (amorphous crystal shape), which is the best in terms thermal and electrical conductivity. Stainless steel is an example for the materials that could be refined in that way, which can be used in variety of applications in the biomedical field and prosthetics inside the human body.

Sunday, 26 June 2022 21:37

"Detection of corona virus using computerized tomography images"

Written by

A group of fifth-grade students discussed a research entitled

"Detection of corona virus using computerized tomography images"

Students names
Youssef Abdul Razzaq Ajeel
Ibrahim Aladdin Mahdi
Maryam Hussein Khalil

 

The names of the discussion commite
Ph.D. Uday Fahd's piety

Asst.Lect. Dalia Mohamed Ali

 

The project based on CT scan chest images which entered into a system (set of codes algorithms) and used matlab to diagnosis COVID19, the program is started by image reading processing and finally covid detection by serial steps. System implements will use colors to label the infected parts of the lung and then shows the results as normal or Covid-infected patient.

Sunday, 26 June 2022 21:28

Mechanical properties of a denture base polymer reinforced with natural and man-made fibers

Written by

Mechanical properties of a denture base polymer reinforced with natural and man-made fibers

Students' names

Ahmed Owaid Thajil
Basmala Hussain Majid
Bara Jassim Hadi
Raneen Fathallah Ghazi

Discussion Committee
Ph.D. Marwan Nafie Ali
Asst.Lect. Dalia Muhammad Ali

Where the research included addressing the problems of fracture of artificial teeth, where the fracture of dentures made of acrylic resin is still an unresolved problem. There is no ideal base material for dentures, but the properties of PMMA can be improved with some reinforcement. Therefore, the aim of this study is to improve the mechanical properties of the denture base material, and this was done by using synthetic glass fibers and natural toothpicks.

  

Sunday, 26 June 2022 21:12

Design and Development of Industrial Monitoring System using LabVIEW

Written by

Design and Development of Industrial Monitoring System using LabVIEW

Students names

 Youssef Abdel Karim

 Zahraa Ghazi Attieh

Zahraa Hussein Hashem

Abdullah Iyad Salem

The names of the discussion committee

Dr. Ziad Qassem

Asst.lect. Diyar Jalal

A health condition monitoring application in LabVIEW will focus on this project. The health conditions will be monitored in real-time using a simulation setup to perform real-time monitoring of crucial health indicators such as temperature, blood pressure, oxygen level and other parameters. LabView software was used to create the system's capabilities successfully. Data from sensors were successfully simulated and logged and shown clearly and concisely. The system's performance was evaluated and found to satisfy the predetermined standards. This system may notify the user if specific parameters exceed or fall below a predetermined threshold by sounding an alarm or displaying a visual indicator. For automation operations, a crucial variable such as temperature, for example, must be monitored to ensure that logic can be included in the control algorithm and an emergency action may be needed.

 

 

 

Sunday, 26 June 2022 20:58

Discussing the research of graduation projects for students of the fifth stage

Written by

Under the patronage of Prof. Dr. Wissam Kazem Hamdan

Head of the Biomedical Engineering Department

In a sober and meticulous scientific atmosphere, the graduation research discussions were conducted

Today and in the classrooms, a discussion of the research of graduation projects for students of the fifth stage and for the morning and evening studies took place, where a number of scientific committees were formed from the professors of the department to manage this discussion sessions. before the committee
The members of the specialized committees discussed urging the students to try to complete as many projects as possible, taking into account the circumstances the students are going through. And directing them to address the problems they encountered during the research period and to develop solutions to the difficulties in the practical aspect.

  

  

 

 

Page 1 of 17
Top